Yamaha Tracer MT09TRA - Owner's Manual > Seats

Instrument and control functions / Seats

Passenger seat

To remove the passenger seat

1. Insert the key into the seat lock, and then turn it counterclockwise.

To remove the passenger seat

  1. Seat lock
  2.  Unlock.

2. Lift the front of the passenger seat and pull it forward.

To install the passenger seat

1. Insert the projections on the rear of the passenger seat into the seat holders as shown, and then push the front of the seat down to lock it in place.

To install the passenger seat

  1. Projection
  2. Seat holder

2. Remove the key.

Rider seat

To remove the rider seat

1. Remove the passenger seat.

2. Remove the cap, then push the rider seat lock lever, located under the back of the rider seat, to the left as shown, and then pull the seat off.

To remove the rider seat

  1. Cap
  2. Rider seat lock lever

To install the rider seat

1. Install the cap with the arrow mark facing forward.

2. Insert the projection on the front of the rider seat into the seat holder as shown, and then push the rear of the seat down to lock it in place.

To install the rider seat

  1. Projection
  2. Seat holder

3. Install the passenger seat.

TIP

Adjusting the rider seat height

The rider seat height can be adjusted to one of two positions to suit the rider's preference.

The rider seat height was adjusted to the lower position at delivery.

Adjusting the rider seat height

  1. Low position
  2. High position

To change the rider seat height to the high position

1. Remove the passenger seat and rider seat.

2. Remove the rider seat height position adjuster by pulling it upward.

To change the rider seat height to the high position

  1. Rider seat height position adjuster

3. Install the rider seat height position adjuster by inserting the front projections into the grommets.

To change the rider seat height to the high position

  1. Rider seat height position adjuster
  2. Projection
  3. Grommet

4. Insert the projection on the front of the rider seat into seat holder B as shown.

To change the rider seat height to the high position

  1. Projection
  2. Seat holder B (for high position)

5. Align the projection on the bottom of the rider seat with the "H" position slot, and then push the rear of the seat down to lock it in place as shown.

To change the rider seat height to the high position

  1. Projection
  2. "H" position slot

6. Install the passenger seat.

To change the rider seat height to the low position

1. Remove the passenger seat and rider seat.

2. Remove the rider seat height position adjuster by pulling it upward.

3. Install the rider seat height position adjuster by inserting the rear projections into the grommets.

To change the rider seat height to the low position

  1. Rider seat height position adjuster
  2. Projection
  3. Grommet

4. Insert the projection on the front of the rider seat into seat holder A as shown.

To change the rider seat height to the low position

  1. Projection
  2. Seat holder A (for low position)

5. Align the projection on the bottom of the rider seat with the "L" position slot, and then push the rear of the seat down to lock it in place as shown.

To change the rider seat height to the low position

  1. Projection
  2. "L" position slot

6. Install the passenger seat.

TIP

Make sure that the seats are properly secured before riding.

See also:

 Yamaha Tracer MT09TRA - Owner's Manual > Traction control system

The traction control system helps maintain traction when accelerating on slippery surfaces, such as unpaved or wet roads. If sensors detect that the rear wheel is starting to slip (uncontrolled spinning), the traction control system assists by regulating engine power as needed until traction is restored.

 Yamaha Tracer MT09TRA - Owner's Manual > Helmet holder

The helmet holder is located under the passenger seat. A helmet holding cable is provided in the owner's tool kit to secure a helmet to the helmet holder. To secure a helmet to the helmet holder

Owner's Manuals

Service manuals